How To Protect The Permanent Magnetic Chuck Under The Condition Of High And Low Temperature?

How to Protect the Permanent Magnetic Chuck under the condition of High and Low Temperature?

 

(1) Add antifreeze.

 

Antifreeze can be used when the temperature is too low and conditions permit. The cooling system should be thoroughly cleaned before use, and antifreeze with good quality and low corrosion should be selected to avoid corrosion of parts due to inferior quality of antifreeze. For equipment that does not use antifreeze in winter, you can add hot water at about 80°C with the water drain switch turned on before use every day, and turn off the water drain switch when the hot water flows out to increase the body temperature; , All water drain switches should be turned on to drain the cooling water. Make the switch still in the open position after draining the water, so as not to drain the water uncleanly.

 

(2) Do a good job of keeping the permanent magnet sucker warm.

 

In winter, the water temperature of the permanent magnetic chuck rises slowly, especially the water temperature is lower. In order to ensure the reliable operation of the permanent magnetic chuck, reduce fuel consumption, and reduce mechanical wear, insulation work must be done well. Generally speaking, a cloth curtain can be added in front of the water tank of the permanent magnetic suction cup to cover the water tank, reduce heat loss, maintain the temperature of the permanent magnetic suction cup, and prevent the temperature from being too low.

 

 

Lifting Weight(t)			5		10			16
Span(m)			Customized
Max. Lifting Height(m)			16		16			16
Speed (m/min)	Hoisting	Electromagnetic	15.6		13			13
	Travelling of Crab		39.5		43.8			44.5
	Travelling of Trolley		92.7	93.7	92.7	93.7	86.4	76	89
Working Class			A5-A8
Electric Current			Three-phase AC 380V 50Hz or Customized

(3) Remove the scale in the water jacket, check and maintain the drain switch.

 

Clean the water jacket of the permanent magnetic suction cup to remove the internal scale to prevent excessive accumulation of scale, which will affect the heat dissipation of the permanent magnetic suction cup and cause the machine temperature to be too high. Do not use bolts or rags for repair or replacement, otherwise it will easily affect the drainage and cause accidents of freezing and cracking parts.

 

(4) Check the working condition of the water-cooled permanent magnet sucker thermostat.

 

Ensure that the thermostat works well to prevent the water temperature of the permanent magnetic sucker from being too low or too high, so as to reduce the wear and tear of the parts. The internal machine is often operated at low temperature, which will cause the multiplication of the wear of the parts. In order to ensure the rapid temperature rise of the permanent magnetic sucker in winter, the thermostat can be removed, but it must be reinstalled before the arrival of summer.

 

(5) Replace the hydraulic or hydraulic transmission oil.

 

Before the arrival of winter, the hydraulic system and hydraulic transmission system of the working device of the equipment should be replaced with hydraulic and hydraulic transmission oil for winter to prevent the hydraulic system and transmission system of the working device from working badly due to the increase in oil viscosity in winter, and even malfunction. The device cannot operate, and the equipment cannot move.

(6) Change the fuel. Choose fuel with low freezing point and good fluidity at low temperature.

 

At low temperature, the viscosity of the fuel increases, the fluidity becomes poor, and the atomization is poor, which leads to the deterioration of the combustion process of the fuel, and the starting performance, power and economy of the permanent magnetic chuck are significantly reduced. Therefore, condensate should be selected under conditions. Point lower fuel. The general selection principle is: the freezing point of the fuel is 6°C lower than the ambient temperature.

 

(7) Replace gear oil and grease.

 

When construction machinery enters winter operation, the transmission, reducer and steering gear should be replaced with winter gear oil, and the wheel bearings should be replaced with low dropping point grease.

 

(8) Change the engine oil.

 

Choose permanent magnet chuck oil with low viscosity. Under low temperature conditions, the viscosity of the engine oil increases with the drop of temperature, the fluidity becomes poor, and the frictional resistance increases, which will cause the permanent magnet chuck to start difficult. Therefore, it should be compensated or eliminated by replacing the oil with a lower viscosity in time adverse effects.